This MAXX Tracer Unit Wire Harness has been redesigned with a voltage regulator built in for added protection with the latest gen PolarStar FCU in min...
Completely Custom USA Machined and Designed NozzleSame or better FPS over existing Bored out Red+ Nozzles20% Larger Bore than current standard Red Noz...
Introducing the new Amped Airsoft Custom Low Flow Pre-Shimmed Poppet in fabulous purple. We've revisited the original poppet design after years of tes...
Specific trigger board for the Ares Amoeba series, Works with all Polarstar engines, except fusion engine.The Blackleaf Airsoft Trigger Board is a "Dr...
Black Leaf Speed Board for P* Jack and F1Improved semi auto trigger response and shorter trigger pullThese are the new v2 version which supports safet...
This HPA version will allow you to connect 1 to 2 solenoids, which makes it compatible with:Polarstar JackPolarstar F2Gate PulsarWolverine Inferno gen...
Tired of endlessly testing your FCU? So are we.
The Gorilla FCU is a control unit designed for any HPA system that gives you the power to adjust your ...
The Gorilla MFCU is not a fire control unit as you know it but designed to fit HPA gearboxes and be a triggerboard at the same time. The Gorilla FCU a...
The A&K SR-25 Spacer Kit comes with a delrin spacer which gets pressed into the front of the Fusion Engine's cylinder to make the Version 2 engine...
This spacer kit allows a V2 Fusion Engine to be used in the A&K and JG SR25 rifles. Since these models use an "V2 Long" gearbox, the standard V2 F...
This switchboard is designed to convert Ares V2 gearboxes equipped with their EFCS MOSFET system and is not compatible with other Ares gearboxes. The ...
This kit is required to mount the original bolt catch and spring found on VFC rifles to the side plate of the V2 Fusion Engine.Included:1x Shoulder Sc...
Forgot to put Loctite on your screws and they disappeared into the black abbess, eh? No worries! This screw set comes with all screws used in the Kyth...
The measured tip length should be within +/- 0.010" of an exiting nozzle to be compatible. If the tip length you measure does not match up to a produc...
This PolarStar Airsoft F2 Gold Low Flow Poppet is a highly anticipated efficiency upgrade that expands the capabilities of the F2 HPA Unit. This Gold ...
The F2™ poppet valve is available in two levels, Red and Gold. The Red valve is the standard valve that comes in the F2 and provides the maximum amoun...
The measured tip length should be within +/- 0.010" of an exiting nozzle to be compatible. If the tip length you measure does not match up to a produc...
This latest Revision 3 Fire Control Unit is for use with PolarStar JACKs, F1s, F2's and Fusion Engines (GEN 2 and Above).Key features of the 2017 R3 F...
This fitting is used in V2, V3 and M240 versions of the Fusion Engine. It is the internal fitting that threads into the engine's cylinder to which the...
Low Flow Poppet Valve for your PolarStar Fusion Engine.This poppet valve has a lower flow than the stock valve which results in the following performa...
The air nozzles for the Fusion Engine come in up to 6 different colours which identify how much the nozzle restricts air flow out of the engine. This ...
Features:Accepts Pressure from 40 PSI to 200 PSIDirect Replacement for Fusion Engine SolenoidsWiring Plug includedThis R107 solenoid is RoHS compliant...
These sets of precision shims are used to secure an HPA cylinder within the gearbox shell to prevent unwanted movement. Since the pins in a gearbox sh...